01Templates & Calculators
RFID Time Clock System: How Badge Time Clocks Work & What to Ask
How an RFID employee time clock works, whether your existing access cards can be reused, what a badge reader needs on site, and what US law asks you to record.
How an RFID Time Clock Works
An RFID time clock has three parts: a card or key fob each employee carries, a reader at the entrance that picks up the card's number when it is tapped, and software that turns the tap into a time record. The card holds only a number; the software knows which employee the number belongs to, whether the tap opens or closes a shift, and what that means for the timesheet.
| Part | What it does | What to check |
|---|---|---|
| Card or fob | Carries a number the reader can pick up from a short distance | The card technology, usually printed on the card or the box it came in |
| Reader | Reads the number and passes it on | It must match the card's frequency and format |
| Terminal | The screen at the door: a tablet, a small PC or a dedicated wall unit | Power, network connection and a mounting spot people actually pass |
| Software | Pairs taps into shifts, builds timesheets and feeds payroll | Approval steps, corrections, exports and who can see what |
Can You Reuse the Access Cards Employees Already Have?
Often yes, and it is the first question to settle, because it decides which reader you buy. Access cards come in two main families that do not read each other:
- 125 kHz proximity cards. The older and still very common type in door access systems. They send a fixed number and are read by low-frequency readers.
- 13.56 MHz smart cards. The newer type, also the frequency of NFC in phones. Some of these cards are encrypted, and an encrypted card may share its number only with a reader that holds the right keys.
Ask the company that installed your door access system which card type and format you have, or read the model number on a card. Then choose a time clock reader for that type. If your cards are encrypted and tied to the access vendor, a second low-cost card or fob just for attendance is sometimes the simpler route.
What You Need on Site
- A reader per entrance. A USB desktop reader plugged into a tablet or PC is the simplest setup; wall-mounted readers suit busy or outdoor entrances.
- Power and network at the mounting spot. A terminal needs both. A local IT or low-voltage contractor can mount the device and run the cable; the software side does not need anyone on site.
- A list of employees and card numbers. Each card number is assigned to one employee record before the first tap.
- A rule for exceptions. Decide who corrects a missed punch and who approves the correction, before the first payroll that depends on it.
This is how Draivix Time & Attendance is set up. The terminal is a kiosk page opened in a browser on a tablet or PC at the entrance, with a card reader connected to it. An employee taps a card and the system decides from the open shift whether this is an arrival or a departure. The terminal signs in with its own token, the card number is checked against the format you set, a double tap within five seconds is ignored, and the terminal cannot send its own time, so backdated punches do not get through. Employees who are not near a terminal clock in from a browser or from a phone with GPS location. Punches are paired into shifts and flow into the timesheet a supervisor approves.
What US Law Asks For
- Federal: accurate records, any method. The FLSA does not require a time clock. Employers may use any timekeeping method they choose, as long as it is complete and accurate, and must keep the hours worked each day and each workweek for every non-exempt employee (DOL Fact Sheet #21).
- California: meal periods and daily overtime. A meal period of at least 30 minutes for a workday over 5 hours (Labor Code § 512) and daily overtime after 8 hours (California Labor Code § 510) mean the record needs meal start and end times and daily totals, not just a weekly number. See the California overtime calculator.
- Illinois: biometric clocks need written consent. The Biometric Information Privacy Act covers identifiers such as fingerprints, hand scans and face geometry, and requires a written policy and a written release before collecting them (740 ILCS 14). A card or fob carries a number, not a biometric identifier, which is one reason employers there choose badges over fingerprint clocks.
Last reviewed: November 18, 2026. This page explains general rules and is not legal advice.
Questions to Ask Before You Buy
- Which card types does the reader support, and will it read the cards we already have?
- Does the terminal keep working, or at least tell us, when the network goes down?
- How is a missed or wrong punch corrected, and is the correction visible afterwards?
- Can supervisors approve timesheets, and can an approved period be locked?
- How do the hours reach payroll: export file, report or direct connection?
- Who installs the hardware at our address, and who supports the software afterwards?
- What happens to our data if we stop using the system?
Tell us how your people clock in today and what your cards are, and we will show you how the terminal, the timesheets and the rest of the company's work fit together: book a consultation.
02Frequently Asked Questions
Can employees use their existing access cards to clock in?
Often yes. The time clock reader has to match the technology of the cards you already have, 125 kHz proximity or 13.56 MHz smart card, and encrypted cards may only work with readers that hold the right keys. Ask your access system installer which card type you have before buying a reader.
Is an RFID time clock a biometric time clock?
No. An RFID card or fob identifies the card, not the person's body. Biometric clocks use fingerprints, hand geometry or face scans, which some states regulate, most notably Illinois under its Biometric Information Privacy Act.
Does US law require a time clock?
No. Under the FLSA, employers may use any timekeeping method they choose, as long as the records are complete and accurate. What is required is the record itself: hours worked each day and each workweek for non-exempt employees.
How do you stop employees from clocking in for each other?
A card can be handed to a coworker, so badge systems rely on policy and review: a written rule against buddy punching, a terminal placed where supervisors can see it, and reports that show unusual patterns. Phone clock-in with GPS location adds a check for people working off site.
Who installs an RFID time clock?
The hardware is simple to mount: a reader and a terminal with power and a network connection. A local IT or low-voltage contractor can install it. The software is set up remotely, including employees, card numbers and approval steps.
03More Free Tools
Related Templates & Calculators
- 2-2-3 Shift Schedule Template (Pitman, Excel & PDF)Free 2-2-3 shift schedule template for four crews on 12-hour shifts, with weekly hours per crew and the workweek start that cuts overtime from 20 hours to 8.Open
- DuPont Schedule Template: 12-Hour Rotation (Excel, PDF)Free DuPont shift schedule template: four crews, 12-hour day and night shifts over a 28-day cycle with a 7-day break. Weekly hours and overtime explained.Open
- ERP RFP Template (Free Excel): Requirements & ScorecardFree ERP RFP template in Excel, no sign-up: 78 requirements in 11 areas, vendor response codes, a weighted scorecard and 15 questions every vendor should answer.Open
- Custom ERP vs. Off-the-Shelf ERP: How to ChooseCustom ERP or off-the-shelf? Compare fit, time to go-live, upgrades, risk and who carries the changes, and see where a configured, tailored system sits between them.Open
Let’s start together
Tell us how your business works.
We will show you what a system that takes over part of that work could look like.
Book a consultation